Premier Control Technologies Logo
Premier Control Technologies Fluid Solutions

Alicat ISMCS - Intrinsically Safe Anti Corrosive Mass Flow Controller

  • Corrosive resistant Zone 0 mass flow controller
  • Full scale flows from 0.5 SCCM up to 100 SLPM
  • Atex II 1G Ex ia IIC T4 Ga / IECEx Ex ia IIC T4 Ga

The New Alicat ISMCS mass flow controller

Alicat ISMCS series of mass flow controllers have been designed for intrinsically safe applications and processes where higher chemical resistance maybe required.

Materials and compatibility

The ISMCS series offers a 316L stainless steel body with FFKM standard elastomers for improved corrosive gas combability, FKM and EPDM elastomers are also available where required.

Compatible gases

ISMCS devices are compatible with an additional 30 gases and gas mixes compared to shared ISMCS mass flow controllers. Every device therefore comes pre-loaded with a choice of 129 user-selectable gases and gas mixes. In addition the user may programme 20 user-defined mixes onto their device with each mix containing up to 5 gases with a 0.01% composition resolution.

Certification and temperature range

All ISMCS are Atex and IECEx Zone 0 certified to II 1G Ex ia IIC T4 Ga / Ex ia IIC T4 Ga both with a -20 °C to +70 °C Tamb rating.

Flow rates and port configurations

The ISMCS series is available with full scale flow rates from 0.5 SCCM up to 100 SLPM with typical port configurations ranging from M5 x 0.8mm female up to ¼” NPT female for higher flow models.
Other thread variants are also available including BSPP, SAE, or Swagelok®-compatible (VCO® and VCR®).

Accuracy and control options

Standard accuracy across all devices is ± 0.8% of reading and ± 0.2% of full scale with optional high accuracy to ± 0.4% of reading and ± 0.2% of full scale.

ISMCS offers a 4 – 20 mA control output / set point input as well as a RS-232 serial communications as standard with optional RS-485 or Modbus RTU (over either RS-232 or RS-485).

Display and ingress protection

Every device also comes with Alicat’s feature rich backlit monochrome display for easy setup and configuration.

Ingress protection is to IP66 with electrical connections being via the DB15 connection port.

Autotune feature and response times

Autotune feature will automatically improve the control performance of the valve and tune the control parameters of the MFC to your application. No PID control setup is needed. Typical control response times are as fast as 30 ms (T63), flow rate dependent and are fully user adjustable. The typical indication response type is < 10 ms, flow rate dependent. Typical warm-up times are less than one second!

Optional relative humidity sensor can compensate for water vapour in hydrogen production calculations, ensuring a prevised measurement of hydrogen output.

On board measurements available

Standard on board measurement and calculation ensure many variables are reported, including:

  • Temperature
  • Mass flow
  • Volumetric flow
  • Absolute pressure
  • Gauge pressure
  • Barometric pressure
  • Relative humidity (with optional RH sensor)
  • Dew point (with optional RH sensor)
  • Percent water vapor (with optional RH sensor)
  • Total mass
  • Total volume

ISMCQS models are also available for higher pressure applications with a P1 inlet pressure of up to 320 PSIA / 22 bara.

Fill out the Configurator Form so our engineers can craft the perfect custom solution for you:

Configure now

Industries

The Alicat ISMCS - Intrinsically Safe Anti Corrosive Mass Flow Controller is widely used in the following industries:

Alicat recalibration service

Alicat Calibration and Service Centre

We provide a certified annual recalibration service on all Alicat mass flow meters and mass flow controllers. Further details on our recalibration service.

Manufacturer

Alicat Scientific